| THIS IS PARTS PAGE 2 |
| Engine Block Spacer fills 20mm or 2cm of space. Stock spacer. Only $4.95 |
| NT Carb with 20mm Slim air box. Fits all motors 50, 70 F80 and other popular engines of the same type that have a 19mm OD intake. Only $19.98 |
| Engine mounting stud M6 extra long. Length is 9.5cm or 3.75 inches. Use this when extra length is needed for your mount.. Only $3.25 Each |
| Exhaust Gasket. High Quality. Fits all Standard DAX Motors and others....Only $1.49 |
| Head Gasket fits all motors with larger 8mm studs. Only $1.99 . |
| High Performance Intake Manifold alloy.19mm OD . Only $2.99 |
| Idler Pulley mounting hardware. Only $4.99 |
| 10 tooth engine sprocket. Run 415 chains or BMX Bicycle chains for lighter weight and more performance. Only $9.49 |
| TYPE= STEEL DISHED SPEED = FAIR CLIMB = VERY GOOD MOUNT=6MM |
| 9 Hole 8mm Mounting rag joint Sprocket Clamp assembly. Only $7.98 |
| 48T |
<---- 8MM
DIAMETER
DIAMETER
| NEEDLE BEARING FOR WRIST PIN AT PISTON. ONLY $4.99 |
| 6MM RAG JOINT SPROCKET MOUNTING HARDWARE. ONLY $7.98. |
6MM SETUP
8MM SETUP
| 41T |
| TYPE = STEEL FLAT SPEED = GREAT CLIMB = GOOD MOUNT=6MM |
| Carburetor Union Washer. A Fresh Air Leak means certain death for any 2 stroke Engine. Install this Fuel Resistant Flat Rubberized Washer to make a seal between your Carb and Intake manifold. This washer fits the 2 stroke NT carburetors. . Only $1.49 |
| 44T |
| THIS IS PARTS PAGE 2 |
| PISTON RING SET HIGH PERFORMANCE 47MM BORE. ONLY $7.49 |
<--- 47mm --->
| HEAD GASKET FITS F60-F65 MOTORS WITH BORE SIZE APPROXIMATELY 44-46MM USING 6MM CYLINDER STUDS. ONLY $1.99 |
<---- 6MM
DIAMETER
DIAMETER
<- 44-46mm ->
| HEAD GASKET FITS F50 MOTORS WITH BORE SIZE NO LARGER THAN 42MM. FITS MOTORS WITH BORE SIZE 36MM-42MM AND 6MM CYLINDER STUDS. ONLY $1.99 |
RATING:
SPEED = BEST !!!
CLIMB = GOOD
SPEED = BEST !!!
CLIMB = GOOD
| Satisfy your need for speed with this 36T Hardened Alloy T6 Racing Sprocket. Uses 6mm 9 hole mount. 3.1mm thickness means you can run BMX chain or 415 chain. Only $34.99 !! |
<- 46-32mm ->
<---- 6MM
DIAMETER
DIAMETER
| 44T sprocket, Dished, Chrome, 8mm 9 hole rag joint set up mounting type. Only $9.99 |
| Engine mounting stud M6 . 1 Inch in length. Can be used for Titan Base Mount to plate. Set of 4. Only $1.99 for a set of four. |
| Get speed and climb with this 41T flat steel sprocket! Uses 6mm 9 hole mounting hardware. Only $12.98 |
| Get speed and climb with this 48T flat steel sprocket! Uses 6mm 9 hole mounting hardware. Only $12.98 |
| 36T |
| Rear axle Mount kick stand steel. Fits bikes with 24, 26, 27 and 700c whees. Will fit other bikes with smaller wheels but you will have to cut it. Add stability to all bikes including those bikes with rear mounted kits. Save your bike from toppling over now !! Get this Rear Axle Mounted kick Stand for only $12.99. Worth every penny !! |
| PISTON RING SET HIGH PERFORMANCE MOLLY. 40MM BORE. ONLY $7.49 |
Specifications:
36T
6061-T6
9 Hole Mount
M6 Holes
Center Hole 35.6mm dia
Sprocket Thickness 3.1mm
weight 115 grams
Flat
36T
6061-T6
9 Hole Mount
M6 Holes
Center Hole 35.6mm dia
Sprocket Thickness 3.1mm
weight 115 grams
Flat
MADE IN USA
| In line fuel filter aluminium High Performance 15,000 microns.Only $4.99 |
7mm
_____
_____
| Fuel Valve for In Line. Control the flow with this new In Line Fuel Valve. Only $8.99. |
____
____
5mm/0.2"od
| 56T SPROCKET, CHROME, DISHED, WILL RUN BMX AND 415 CHAINS AND OTHER 1/2 CHAINS. USES 6MM 9 HOLE MOUNTING HARDWARE. Only $24.99 |
| CLUTCH PIN AND BEARING. Only $1.99 |
| NT CARB FLOAT WHITE PLASTIC DONUT. ONLY $4.49 |
| CRANK SEAL 14.8x27x7.5mm. Only $2.99 |
| GEAR BOX 10T STEEL FLAT 1/2 INCH DRIVE 6 COG SPLINE. ONLY $4.99 |
| GEAR BOX 3:1 EXTENDED 2 IN/5CM OUTPUT SHAFT FOR IN FRAME SETUPS NEEDING OFFSET. USES INTERNAL #35 RACING CHAIN GREASED WITH 6 COG SPLINE, 4 BOLT PATTERN. ONLY $39.99 . |
| PROTECTED BY COPYRIGHT VAu 1-068-735 |
| 72T T8F 8mm/05T STEEL RACING SPROCKET WITH 8MM MOUNTING 9 HOLES. USE WITH 3:1 AND 5:1 GEAR BOX FOR SUPERIOR RESULTS !! ONLY $24.99 |
| T8F 8MM 05T CHAIN 100 LINKS 62 IN/160CM LENGTH. WORKS SUPERB WITH 3:1 GEAR BOX AND 72T REAR SPROCKET. ONLY $16.99 |
| PROTECTED BY COPYRIGHT VAu 1-068-735 |
| 11T 8MM T8F 05T STEEL SPROCKET. ONLY $7.99 |
| 14T 8MM T8F 05T STEEL SPROCKET. ONLY $8.99 |
| 20T 8MM T8F 05T STEEL SPROCKET. ONLY $9.99 |
BEST FOR CLIMB
BEST FOR SPEED
| 37mm |
| PTO SPROCKET RETAINER CLIP "SNAP RING". KEEPS SPROCKET ON TO THE SPLINE SHAFT OF THE PTO UNIT. ONLY $1.99 |
_
_
_
_
_
_
_
_
_
_
| 19mm OD |
| 33mm CTC |
| OUT OF STOCK |
| DAX CENTER STAND DOUBLE STAND ALLOY BLACK. Very nice and weighs only 560grams or 20oz and can hOLD bikes up to 90lbs. Fits 24-29 inch 700c wheel bikes. Only $24.99 |
| DAX ALLOY CENTER STAND ! WOW ! |
| LONG TUBE HEADER CHROME, ALSO KNOWN AS POO POO PIPE. Fits F50-F80 engines and 4 Strokes engines as well . ONLY $49.99 |